Careers

General Inquiries
To further explore any opportunities mentioned on this page or to apply for other positions not listed please apply online.

Perfection Servo Hydraulics, Inc.
Human Resources Department
1290 Lyon Road
Batavia, IL 60510
Phone:630-628-2800, Ext 544

For a list of our company benefits please click here

Perfection Servo Hydraulics is an equal opportunity employer and provides a drug-free work environment.

Click here for Hydraulic Internship info

Current Openings

Servo Motor Technician

Job Summary

The position is responsible for the repair of all servo motors done at Perfection Servo Hydraulics.

Responsibilities

Repair job sheets to determine: job status, work authorization/limitations, estimate, description of problems, and/or expected serviceability
Test electro-mechanical equipment to troubleshoot known or suspected problems using various methods (ac or dc)
Disassemble electro-mechanical equipment noting parts identification, configuration and condition
Clean electro-mechanical equipment assemblies as needed using various methods and steps, including, but not limited to: parts washers/steamers, caustic tanks, glass beaders, etc.
Measure for or note proper replacement parts. Correctly requisition needed items, as approved by supervisor
Replace or repair worn or defective mechanical or electro-mechanical assemblies, including, but not limited to: bearings, brushes, brush holders, motor leads, gears, seals, impellers, mechanical switches, brakes, clutches, clutch rotors, tachs, fans, end shields, etc.
Retest reassembled electro-mechanical equipment for proper output and operation
Complete required paperwork for each job accurately and on a timely basis
Operate specialized repair and testing equipment and other equipment as needed
Observe all safety procedures and use proper protective gear (especially eye and ear protection)
Lift, tighten, adjust and/or secure heavy objects in order to perform work duties.
Keep work area neat and clean as directed by supervisor
Repair a servo motor without spec sheet or previous history (level 3)
Train other technicians or assist with any questions (level 3)
Other projects and responsibilities may be added at the company's discretion.

Required skills

Education or experience:

Possession of high school diploma or equivalent (GED)
6 months to 1 year experience in servo motor prep (level 1)
1+ year experience repairing servo motors or completion of manufacturer's certification/ training on motor repair

Basic mechanical aptitude
Ability to understand, perform and retain various skill-related training and operational safety procedures demonstrated by supervisor
Familiarity with encoders, resolvers, tachs, stators and armatures
Possesses the ability to be trained to repair standard AC motors and to recognize basic motor parts like bearings, stators and housings (level 1)
Possesses the ability to trouble shoot a servo motor (level 3)
Possesses the ability to repair a servo motor without spec sheet or previous history (level 3)
Possesses the ability to train other technicians or assist with any questions (level 3)
Ability to communicate with co-workers, management, vendors, suppliers, and others in a courteous and professional manner
Possesses strong organizational skills

Other Information
Special Information (travel required, physical requirements, additional info):

Ability to rewind motors is a plus
Understanding of electronics is a plus
40-50 hours per week, occasional overtime may be required

LIMITATIONS AND DISCLAIMER
The above job description is meant to describe the general nature of the work being performed; it is not intended to be construed as an exhaustive list of all responsibilities, duties and skills required for the position. Continued employment remains on an “at-will” basis.

APPLY ONLINE PDF

Electronic Technician

Job Summary

The electronics technician is responsible for trouble shooting, repairing and testing various electronic drives, controllers and pc boards.

Responsibilities

Repair electronic drives, controllers and pc boards.
Troubleshoot and test electronic components to board level, using various methods and testing equipment
Follow company procedures for requisitioning parts
Repair and/or replace electronic components to board level, including but not limited to: diodes, transistors, resistors, capacitors, integrated circuits, other printed circuit components, etc.
Verify repairs using start-up testing procedures
Operate specialized equipment, including but not limited to: oscilloscopes, megohmmeters, high voltage insulation testers, ac/dc volt-ohm-milliammeters, clamp-on ammeters, various test panels, soldering equipment, infrared scanning equipment, various kinds of hand-held power and non-power tools etc.
Document all test procedures and add them to Perfection’s library
Complete all paperwork and service reports on repaired job
Keep work area neat and clean as directed by supervisor
Other projects and responsibilities may be added at the company's discretion.

Required skills

Education or experience: Associates degree in electronics preferred, but not required

Ability to solder/desolder
Thorough understanding of electronic circuitry
Ability to recognize different electronic components as their functions
Familiarity with and ability to utilize different types of test equipment such as function generators, oscilloscopes, digital multimeters, and power supplies.
Possesses strong communication skills

Other Information
Special Information (travel required, physical requirements, additional info):
·        Some traveling may be required for service calls
·        40-50 hours per week, occasional overtime may be required
·        Industrial electronic experience is a plus

LIMITATIONS AND DISCLAIMER
The above job description is meant to describe the general nature of the work being performed; it is not intended to be construed as an exhaustive list of all responsibilities, duties and skills required for the position. Continued employment remains on an “at-will” basis.

APPLY ONLINE    PDF

Hydraulic Technician

Job Summary

The hydraulic technician is responsible for testing and repairing various hydraulic components.

Responsibilities

Performing shop maintenance
Testing and evaluating incoming hydraulic units
Rebuilding hydraulic components
Apply mechanical concepts and best practices
Troubleshooting hydraulic systems
Train and develop staff (level 3)
Other projects and responsibilities may be added at the company’s discretion.

Required skills

Education or experience: Possession of high school diploma or equivalent (GED), possess mechanical ability and has completed some technical training or hands on experience with hydraulics.

Ability to set up and test servo valves
Ability to use a variety of measuring tool such as micrometers, ID micrometers, calipers, and voltage meters
Able to use electrical test equipment
Possesses mechanical ability

Other Information
Special Information (travel required, physical requirements, additional info):

Regularly required to stand, sit, bend and lift up to 50 pounds
Ability to carry out multiple tasks simultaneously in a fast paced shop environment
Advanced hydraulics coursework is a plus
40-50 hours per week, overtime may be required

APPLY ONLINE PDF

Servo and Proportional Valve Technician

Job Summary

The servo and proportional valve technician is responsible for rebuilding and testing various servo valves and proportional valves.

Responsibilities

Testing servo valves to the Original Equipment Manufacturer’s specifications
Rebuilding servo valves and proportional valves
Running in or evaluating servo valves and proportional valves
Making shipping plates
Other projects and responsibilities may be added at the company’s discretion.

Required skills

Education or experience: Possession of high school diploma or equivalent (GED)

Ability to set up and test servo valves
Ability to use a variety of measuring tool such as micrometers, ID micrometers, calipers, and voltage meters
Able to use electrical test equipment
Possesses mechanical ability

Other Information

Special Information (travel required, physical requirements, additional info):

Regularly required to stand, sit, bend and lift up to 50 pounds
Ability to carry out multiple tasks simultaneously in a fast paced shop environment
Ability to read blueprints is a plus
40-50 hours per week, overtime may be required

APPLY ONLINE PDF